El Diablo Chrome 17" Rise Universal Ape Hangers 1-1/4" Diameter Handlebars 2007-2009 Honda VT750C2 Shadow Spirit

"EL DIABLO" CHROME  APEHANGERS
17" Rise 1-1/4" Handlebars




Fits 2007 - 2009 Honda VT750C2 Shadow Spirit



  • El Diablo ape hangers provides the bad-boy image and "old school biker" attitude but with a twist and cool look to fit your metric cruiser

  • Demon's cycle specially designed and engineered the height, bends and tubing thickness to provide a cool look while improving comfort and control

  • You'll find your arms are allowed to hang and drape effortlessly, and your bike's front end become easier to control

  • The massive 1-1/4” tubing and the cool bad-boy biker look of these bars truly makes you a standout in the crowd

  • Bar rise is 17", a height we engineered, evaluated, tested and proved was the best choice for today’s metric cruisers with riser spacing of 3-1/2" to 4" and as the best possible fit for most riders 

  • Each handlebar is bored and dimpled to allow for internal wiring can very easy be custom fitted on metric cruisers if riser spacing of 3-1/2" to 4"

  • Requires longer control cables, but most stock 1" type controls

  • Fits bikes with riser spacing of 3-1/2" to 4"

  • Works with most stock and aftermarket risers

  • Diameter: 1-1/4"

  • Width: 37"

  • Rise: 17"



 

Chrome

 










 




 









How to Install New Handlebar



Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.



  1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are


fabricated from 1 1/4"-inch tubing and powder coated black.


2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.


3. The new handlebars have oblong holes to run the control wiring in and out through.


4.  air nozzle is used to blow the lead  string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.


5. The rope was used to pull the controls wire harnesses through the bars.


6. The factory risers wer used to mount the new bars.


7. Because the bars are T inch in diameter at  their center mounting position, a stock
clamp was used


8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.


9. The switch wiring exits the front of the switch housing and into the bars.


10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars


11. These stunning bars sure remind us of devil wings.


Product ID: 4463
SKU: 17 Chrome El Diablo Honda VT750C2 7118-C

Availability: In stock

$139.00
  • Details
    Details
    "EL DIABLO" CHROME  APEHANGERS
    17" Rise 1-1/4" Handlebars


    Fits 2007 - 2009 Honda VT750C2 Shadow Spirit
    • El Diablo ape hangers provides the bad-boy image and "old school biker" attitude but with a twist and cool look to fit your metric cruiser
    • Demon's cycle specially designed and engineered the height, bends and tubing thickness to provide a cool look while improving comfort and control
    • You'll find your arms are allowed to hang and drape effortlessly, and your bike's front end become easier to control
    • The massive 1-1/4” tubing and the cool bad-boy biker look of these bars truly makes you a standout in the crowd
    • Bar rise is 17", a height we engineered, evaluated, tested and proved was the best choice for today’s metric cruisers with riser spacing of 3-1/2" to 4" and as the best possible fit for most riders 
    • Each handlebar is bored and dimpled to allow for internal wiring can very easy be custom fitted on metric cruisers if riser spacing of 3-1/2" to 4"
    • Requires longer control cables, but most stock 1" type controls
    • Fits bikes with riser spacing of 3-1/2" to 4"
    • Works with most stock and aftermarket risers
    • Diameter: 1-1/4"
    • Width: 37"
    • Rise: 17"
     
    Chrome

     

     

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4"-inch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Reviews
    Write Your Own Review

    Only registered users can write reviews. Please, log in or register

    Tags

    Use spaces to separate tags. Use single quotes (') for phrases.