Chrome 9" Rise Universal Ape Hangers "Frisco" Chubby 1-1/4" Diameter Handlebars for Harley Motorcycles

"CHUBBY FRISCO" CHROME UNIVERSAL APEHANGERS
9" Rise 1-1/4" Handlebars


To fit Harley-Davidson FLST, FXST, Sportster XL (1200, Iron 883,Super Low, Seventy Two, Forty Eight, Street Bob, Fat Bob, Switchback)  including Throttle-by-wire models, and any custom application.

 

Chopper freaks in the 1960's cooked up some pretty wild handlebars for their custom death traps, especially in California's fabled San Francisco Bay Area. Chubby Frisco bar pays homage to the bikes of guys like Sonny Barger, Arlen Ness and Tobie Gene Levingston.

 

Triple plated chrome!
9" rise. 6" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
3-1/2 on-center knurling for firm mounting.
34-1/2" wide from tip to tip.
Come with drilled wiring holes.

 

Chrome finish









 




 









How to Install New Handlebar



Ever notice how most fine artists depict the devil? They draw this demon
from hells wings as having sharp angles. This vision was not lost on
Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
devil wings. No matter the imagery, we thought they have a real cool look, as
did Navy Seaman Mario Guerrero.



  1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are


fabricated from 1 1/4-nch tubing and powder coated black.


2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.


3. The new handlebars have oblong holes to run the control wiring in and out through.


4.  air nozzle is used to blow the lead  string through the bars,Then a length of
rope is attached to the string and pulled through
the bars.


5. The rope was used to pull the controls wire harnesses through the bars.


6. The factory risers wer used to mount the new bars.


7. Because the bars are T inch in diameter at  their center mounting position, a stock
clamp was used


8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.


9. The switch wiring exits the front of the switch housing and into the bars.


10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars


11. These stunning bars sure remind us of devil wings.


Product ID: 4660
SKU: Chrome 9 Frisco

Availability: In stock

$99.99
  • Details
    Details
    "CHUBBY FRISCO" CHROME UNIVERSAL APEHANGERS
    9" Rise 1-1/4" Handlebars


    To fit Harley-Davidson FLST, FXST, Sportster XL (1200, Iron 883,Super Low, Seventy Two, Forty Eight, Street Bob, Fat Bob, Switchback)  including Throttle-by-wire models, and any custom application.
     
    Chopper freaks in the 1960's cooked up some pretty wild handlebars for their custom death traps, especially in California's fabled San Francisco Bay Area. Chubby Frisco bar pays homage to the bikes of guys like Sonny Barger, Arlen Ness and Tobie Gene Levingston.
     
    Triple plated chrome!
    9" rise. 6" backward sweep. 1 1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
    3-1/2 on-center knurling for firm mounting.
    34-1/2" wide from tip to tip.
    Come with drilled wiring holes.
     
    Chrome finish

     

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4"-inch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Reviews
    Write Your Own Review

    Only registered users can write reviews. Please, log in or register

    Tags

    Use spaces to separate tags. Use single quotes (') for phrases.

    You may also be interested in the following product(s)