Welcome to Demon's Cycle Inc.

Your Shopping cart is empty.

Skip to Main Content »

Dresser Bagger Parts

Items 1 to 24 of 43 total

per page

Grid  List 

Set Descending Direction
  1. Mayhem Chrome 15" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles

    Mayhem Chrome 15" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles

    $199.99

    "MAYHEM" CHROME APEHANGERS
    15" Rise 1-1/4" Handlebars


    To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present including.
    May work on throttle-by-wire models with custom fitting and any custom application.
     
    These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.

    IMPORTANT: Unlike the cheap bars that our competitors sell we do not use pipe-in-pipe construction. Welded or glued joints on cheap handlebars tend to fail and handlebars simply fall apart collapse during a ride. Imagine what that catastrophic failure leads to.
    Our handlebars use one piece technology. There are no joints in 1"-to"-1.25" transitions. Solid one piece pipe will not fail!
     
    Triple Plated Chrome!
    15" rise. 9" backward sweep.
    1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
    3-1/2 on-center knurling for firm mounting.
    39-1/2" wide from tip to tip.
    Come with drilled wiring holes.
     
    Chrome finish

    Learn More
  2. 21x3.5" Black Mammoth 48 Fat Spokes Front Wheel for Harley-Davidson Dual Disc

    21" x3.5" Black Mammoth 48 Fat Spokes Front Wheel for Harley-Davidson FL Dual Disc 25MM ABS Bearings Dresser Bagger

    $399.00

    21" x 3.5" Black 48 Fat Spokes Front Wheel

    BLACK with BILLET HUB
    MAMMOTH 48 SMOOTH SPOKES


    To fit any Harley-Davidson Dual Disc models and custom application

     
    21" x 3.5" Dual disc front for 25MM axle and ABS Bearings!
    This is the best spoked wheel you can get. The craftsmanship and quality are surpassed by none. The thick spokes are chromed, Billet hub and rim are powder coated black.
     
    Wheel comes with black billet hub and sealed bearings, sealed for TUBELESS application
     
    Sets available
     

    Learn More
  3. 18" Rise Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles

    18" Rise Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles

    $555.55

    Chrome 18" Rise 'El Diablo' Ape Hangers
    with Hand Control Kit
    and Chrome Switches

    For Harley-Davidson Touring (Dresser / Bagger) models W/ Cruise Control from 1996 to 2012

    May work on throttle-by-wire models with custom fitting and any custom application

    (Only for models with just CRUISE and RADIO)

    This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.

    All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
    Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.

    This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.

    Here is what you are getting:

    Smooth-Contour Hand Controls
    Unique design has hidden underside mounting
    on the switch housings for
    an unobstructed smooth, rounded surface on the top housing.
    BETTER LOOK AND CHROME THAN ANY HD PRODUCT.
    11/16" Bore master cylinder. For dual disc application.
    with radio controls and  cruise control

    This is top quality kit.
    Much higher quality than HD or any aftermarket product. Simply the best.


    Retail $402.99

    ----------------------------------------------------------------


    Chrome 'El Diablo'
    Swedged Apehangers
    18" Rise 1-1/4" Handlebars
    for Bagggers/Dressers

    Show chromed!
    18" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
    37" wide from tip to tip.
    Come with drilled wiring holes.

    Retail $210.99

    --------------------------------------------------------------

    Chrome Switches and Wire Harness

    High quality chrome switches for Dresser hand controls with radio control and cruise control.
    Wires are soldered and color-coded for easy installation.

    Retail $206.99

    ---------------------------------------------------------------

    Total package price: 402.99
    210.99
    206.99
    Professional Installation 235.00
    _________________
    Total: $1055.97

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4-nch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Learn More
  4. 16" Rise Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles

    16" Rise Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles

    $555.55

    Chrome 16" Rise 'El Diablo' Ape Hangers
    with Hand Control Kit
    and Chrome Switches

    For Harley-Davidson Touring (Dresser / Bagger) models W/ Cruise Control from 1996 to 2007

    May work on throttle-by-wire models with custom fitting and any custom application

    This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.

    All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
    Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.

    This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.

    Here is what you are getting:

    Smooth-Contour Hand Controls
    Unique design has hidden underside mounting
    on the switch housings for
    an unobstructed smooth, rounded surface on the top housing.
    BETTER LOOK AND CHROME THAN ANY HD PRODUCT.
    11/16" Bore master cylinder. For dual disc application.
    with radio controls and  cruise control

    This is top quality kit.
    Much higher quality than HD or any aftermarket product. Simply the best.


    Retail $402.99

    ----------------------------------------------------------------


    Chrome 'El Diablo'
    Swedged Apehangers
    16" Rise 1-1/4" Handlebars
    for Bagggers/Dressers

    Show chromed!
    16" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
    37" wide from tip to tip.
    Come with drilled wiring holes.

    Retail $210.99

    --------------------------------------------------------------

    Chrome Switches and Wire Harness

    High quality chrome switches for Dresser hand controls with radio control and cruise control.
    Wires are soldered and color-coded for easy installation.

    Retail $206.99

    ---------------------------------------------------------------

    Total package price: 402.99
    210.99
    206.99
    Professional Installation 235.00
    _________________
    Total: $1055.97

     

     

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4-nch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Learn More
  5. 14" Rise Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles

    14" Rise Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles

    $555.55

    Chrome 14" Rise 'El Diablo' Ape Hangers
    with Hand Control Kit
    and Chrome Switches

    For Harley-Davidson Touring (Dresser / Bagger) models W/ Cruise Control from 1996 to 2012

    May work on throttle-by-wire models with custom fitting and any custom application

    (Only for models with CRUISE and RADIO ONLY)

    This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.

    All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
    Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.

    This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.

    Here is what you are getting:

    Smooth-Contour Hand Controls
    Unique design has hidden underside mounting
    on the switch housings for
    an unobstructed smooth, rounded surface on the top housing.
    BETTER LOOK AND CHROME THAN ANY HD PRODUCT.
    11/16" Bore master cylinder. For dual disc application.
    with radio controls and  cruise control

    This is top quality kit.
    Much higher quality than HD or any aftermarket product. Simply the best.


    Retail $402.99

    ----------------------------------------------------------------


    Chrome 'El Diablo'
    Swedged Apehangers
    14" Rise 1-1/4" Handlebars
    for Bagggers/Dressers

    Show chromed!
    14" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
    37" wide from tip to tip.
    Come with drilled wiring holes.

    Retail $210.99

    --------------------------------------------------------------

    Chrome Switches and Wire Harness

    High quality chrome switches for Dresser hand controls with radio control and cruise control.
    Wires are soldered and color-coded for easy installation.

    Retail $206.99

    ---------------------------------------------------------------

    Total package price: 402.99
    210.99
    206.99
    Professional Installation 235.00
    _________________
    Total: $1055.97

     

     

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4-nch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Learn More
  6. 12" Rise Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles

    12" Rise Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles

    $555.55

    Chrome 12" Rise 'El Diablo' Ape Hangers
    with Hand Control Kit
    and Chrome Switches

    For Harley-Davidson Touring (Dresser / Bagger) models W/ Cruise Control from 1996 to 2007

    (Only for models with CRUISE and RADIO ONLY)

    This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.

    All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
    Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.

    This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.

    Here is what you are getting:

    Smooth-Contour Hand Controls
    Unique design has hidden underside mounting
    on the switch housings for
    an unobstructed smooth, rounded surface on the top housing.
    BETTER LOOK AND CHROME THAN ANY HD PRODUCT.
    11/16" Bore master cylinder. For dual disc application.
    with radio controls and  cruise control

    This is top quality kit.
    Much higher quality than HD or any aftermarket product. Simply the best.


    Retail $402.99

    ----------------------------------------------------------------


    Chrome 'El Diablo'
    Swedged Apehangers
    12" Rise 1-1/4" Handlebars
    for Bagggers/Dressers

    Show chromed!
    14" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
    37" wide from tip to tip.
    Come with drilled wiring holes.

    Retail $210.99

    --------------------------------------------------------------

    Chrome Switches and Wire Harness

    High quality chrome switches for Dresser hand controls with radio control and cruise control.
    Wires are soldered and color-coded for easy installation.

    Retail $206.99

    ---------------------------------------------------------------

    Total package price: 402.99
    210.99
    206.99
    Professional Installation 235.00
    _________________
    Total: $1055.97

     

     

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4-nch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Learn More
  7. 12" Rise Black Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles

    12" Rise Black Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles

    $555.55

    Black 12" Rise 'El Diablo' Ape Hangers
    with Hand Control Kit
    and Chrome Switches

    For Harley-Davidson Touring (Dresser / Bagger) models W/ Cruise Control from 1996 to 2012

    May work on throttle-by-wire models with custom fitting and any custom application

    (Only for models with CRUISE and RADIO ONLY)

    This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.

    All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
    Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.

    This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.

    Here is what you are getting:

    Smooth-Contour Hand Controls
    Unique design has hidden underside mounting
    on the switch housings for
    an unobstructed smooth, rounded surface on the top housing.
    BETTER LOOK AND CHROME THAN ANY HD PRODUCT.
    11/16" Bore master cylinder. For dual disc application.
    with radio controls and  cruise control

    This is top quality kit.
    Much higher quality than HD or any aftermarket product. Simply the best.


    Retail $402.99

    ----------------------------------------------------------------


    Black 'El Diablo'
    Swedged Apehangers
    12" Rise 1-1/4" Handlebars
    for Bagggers/Dressers

    Show Black!
    12" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
    37" wide from tip to tip.
    Come with drilled wiring holes.

    Retail $210.99

    --------------------------------------------------------------

    Chrome Switches and Wire Harness

    High quality chrome switches for Dresser hand controls with radio control and cruise control.
    Wires are soldered and color-coded for easy installation.

    Retail $206.99

    ---------------------------------------------------------------

    Total package price: 402.99
    210.99
    206.99
    Professional Installation 235.00
    _________________
    Total: $1055.97

     

     

     

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4-nch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Learn More
  8. 14" Rise Black Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers With Cruise Control 1996-2012 Motorcycles

    14" Rise Black Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers With Cruise Control 1996-2012 Motorcycles

    $555.55

    Black 14" Rise 'El Diablo' Ape Hangers
    with Hand Control Kit
    and Chrome Switches W/ Cruise Crontrol

    For Harley-Davidson Touring (Dresser / Bagger) models with Cruise Control from 1996 to 2012

    May work on throttle-by-wire models with custom fitting and any custom application

    (Only for models with CRUISE and RADIO ONLY)

    This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.

    All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
    Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.

    This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.

    Here is what you are getting:

    Smooth-Contour Hand Controls
    Unique design has hidden underside mounting
    on the switch housings for
    an unobstructed smooth, rounded surface on the top housing.
    BETTER LOOK AND CHROME THAN ANY HD PRODUCT.
    11/16" Bore master cylinder. For dual disc application.
    with radio controls and  cruise control

    This is top quality kit.
    Much higher quality than HD or any aftermarket product. Simply the best.


    Retail $402.99

    ----------------------------------------------------------------


    Black 'El Diablo'
    Swedged Apehangers
    14" Rise 1-1/4" Handlebars
    for Bagggers/Dressers

    Show Black!
    14" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
    37" wide from tip to tip.
    Come with drilled wiring holes.

    Retail $210.99

    --------------------------------------------------------------

    Chrome Switches and Wire Harness

    High quality chrome switches for Dresser hand controls with radio control and cruise control.
    Wires are soldered and color-coded for easy installation.

    Retail $206.99

    ---------------------------------------------------------------

    Total package price: 402.99
    210.99
    206.99
    Professional Installation 235.00
    _________________
    Total: $1055.97

     

     

     

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4"-inch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Learn More
  9. 16" Rise Black Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers With Cruise Control 1996-2012 Motorcycles

    16" Rise Black Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers With Cruise Control 1996-2012 Motorcycles

    $555.55

    Black 16" Rise 'El Diablo' Ape Hangers
    with Hand Control Kit
    and Chrome Switches

    For Harley-Davidson Touring (Dresser / Bagger) models from 1996 to 2012

    May work on throttle-by-wire models with custom fitting and any custom application

    (Only for models with RADIO and CRUISE ONLY)

    This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.

    All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
    Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.

    This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.

    Here is what you are getting:

    Smooth-Contour Hand Controls
    Unique design has hidden underside mounting
    on the switch housings for
    an unobstructed smooth, rounded surface on the top housing.
    BETTER LOOK AND CHROME THAN ANY HD PRODUCT.
    11/16" Bore master cylinder. For dual disc application.
    with radio controls and  cruise control

    This is top quality kit.
    Much higher quality than HD or any aftermarket product. Simply the best.


    Retail $402.99

    ----------------------------------------------------------------


    Black 'El Diablo'
    Swedged Apehangers
    16" Rise 1-1/4" Handlebars
    for Bagggers/Dressers

    Show Black!
    16" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
    37" wide from tip to tip.
    Come with drilled wiring holes.

    Retail $210.99

    --------------------------------------------------------------

    Chrome Switches and Wire Harness

    High quality chrome switches for Dresser hand controls with radio control and  cruise control.
    Wires are soldered and color-coded for easy installation.

    Retail $206.99

    ---------------------------------------------------------------

    Total package price: 402.99
    210.99
    206.99
    Professional Installation 235.00
    _________________
    Total: $1055.97

     

     

     

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4"-inch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Learn More
  10. 18" Rise Black Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls  for Harley Dressers Baggers With Cruise Control 1996-2012 Motorcycles

    18" Rise Black Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers With Cruise Control 1996-2012 Motorcycles

    $555.55

    Black 18" Rise 'El Diablo' Ape Hangers
    with Hand Control Kit
    and Chrome Switches

    For Harley-Davidson Touring (Dresser / Bagger) models W/ Cruise Control from 1996 to 2012

    May work on throttle-by-wire models with custom fitting and any custom application

    (Only for models with RADIO and CRUISE ONLY)

    This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.

    All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
    Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.

    This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.

    Here is what you are getting:

    Smooth-Contour Hand Controls
    Unique design has hidden underside mounting
    on the switch housings for
    an unobstructed smooth, rounded surface on the top housing.
    BETTER LOOK AND CHROME THAN ANY HD PRODUCT.
    11/16" Bore master cylinder. For dual disc application.
    with radio controls and  cruise control

    This is top quality kit.
    Much higher quality than HD or any aftermarket product. Simply the best.


    Retail $402.99

    ----------------------------------------------------------------


    Black 'El Diablo'
    Swedged Apehangers
    18" Rise 1-1/4" Handlebars
    for Bagggers/Dressers

    Show Black!
    18" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
    37" wide from tip to tip.
    Come with drilled wiring holes.

    Retail $210.99

    --------------------------------------------------------------

    Chrome Switches and Wire Harness

    High quality chrome switches for Dresser hand controls with radio control and cruise control.
    Wires are soldered and color-coded for easy installation.

    Retail $206.99

    ---------------------------------------------------------------

    Total package price: 402.99
    210.99
    206.99
    Professional Installation 235.00
    _________________
    Total: $1055.97

     

     

     

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4-nch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Learn More
  11. El Diablo Chrome 18" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles

    Clearance Sale! El Diablo Chrome 18" Rise Ape Hangers 1-1/4" Diameter Handlebars Harley Dressers Baggers FLHT FLHTC Motorcycles

    $139.00

    Clearance Sale!
    Need to make room on shelves. Limited time sale! Get them while they last!

    "EL DIABLO" CHROME APEHANGERS
    18" Rise 1-1/4" Handlebars


    To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present
    . May work on throttle-by-wire models with custom fitting and any custom application.
     
    These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.
     
    Triple-plated chrome!
    18" rise. 11" backward sweep.
    1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
    3-1/2 on-center knurling for firm mounting.
    37" wide from tip to tip.
    Come with drilled wiring holes.
     
    Chrome finish

     

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4-nch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Learn More
  12. 23" x 3.5" Black 80 Spokes Front Wheel for Harley-Davidson Dual Disc 25MM ABS Bearings

    23" x 3.5" Black 80 Spokes Front Wheel for Harley-Davidson Dual Disc 25MM ABS Bearings

    $400.00

    23" x 3.5" Black 80 Spokes Front Wide Glide Wheel

    BLACK with BILLET HUB
    Black Rims & Hub, Chrome Spokes


    To fit any Harley-Davidson Dual Disc models and custom application

     
    23" x 3.5" Dual disc front for 25MM axle and ABS Bearings!
    This is the best spoked wheel you can get. The craftsmanship and quality are surpassed by none. The spokes are chromed, Billet hub and rim are powder coated black.
     
    Wheel comes with black billet hub and sealed bearings, sealed for TUBELESS application
     
    Sets available
     

    Learn More
  13. Mayhem Chrome 17" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles

    Mayhem Chrome 17" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles

    $199.99

    "MAYHEM" CHROME APEHANGERS
    17" Rise 1-1/4" Handlebars


    To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present including.
    May work on throttle-by-wire models with custom fitting and any custom application.
     
    These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.

    IMPORTANT: Unlike the cheap bars that our competitors sell we do not use pipe-in-pipe construction. Welded or glued joints on cheap handlebars tend to fail and handlebars simply fall apart collapse during a ride. Imagine what that catastrophic failure leads to.
    Our handlebars use one piece technology. There are no joints in 1"-to"-1.25" transitions. Solid one piece pipe will not fail!
     
    Triple Plated Chrome!
    17" rise. 9" backward sweep.
    1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
    3-1/2 on-center knurling for firm mounting.
    39-1/2" wide from tip to tip.
    Come with drilled wiring holes.
     
    Chrome finish

    Learn More
  14. Mayhem Chrome 16" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles

    Mayhem Chrome 16" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles

    $199.99

    "MAYHEM" CHROME APEHANGERS
    16" Rise 1-1/4" Handlebars


    To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present including.
    May work on throttle-by-wire models with custom fitting and any custom application.
     
    These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.

    IMPORTANT: Unlike the cheap bars that our competitors sell we do not use pipe-in-pipe construction. Welded or glued joints on cheap handlebars tend to fail and handlebars simply fall apart collapse during a ride. Imagine what that catastrophic failure leads to.
    Our handlebars use one piece technology. There are no joints in 1"-to"-1.25" transitions. Solid one piece pipe will not fail!
     
    Triple Plated Chrome!
    16" rise. 9" backward sweep.
    1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
    3-1/2 on-center knurling for firm mounting.
    39-1/2" wide from tip to tip.
    Come with drilled wiring holes.
     
    Chrome finish

    Learn More
  15. 23" x 3.5" 80 Spoke Black Billet Hub Front Wide Glide Wheel for Harley Davidson FL Dresser Dual Disc

    23" x 3.5" 80 Spoke Black Billet Hub Front Wide Glide Wheel for Harley Davidson FL Dresser Dual Disc

    $400.00

    23" x 3.5" Black 80 Spokes Front Dual Disc Wide Glide Wheel


    CUSTOM HEAVY DUTY 80 SPOKE FRONT WHEEL FOR HARLEY-DAVIDSON.
    with BLACK BILLET HUB
    23" x 3.5" Rim

    To fit 1984 - 2007 Harley-Davidson Dual Disc Wide Glide models and Custom Application.
    23" x 3.5"


    Dual Disc


    This is heavy duty, top quality 80 spokes chrome front wheel.
    This wheel comes with billet hub, and bearings and center spacers for 3/4" & 1" axles!


     

    Learn More
  16. 4" Harley-Davidson FLH FLT Dresser Road King Exhaust Mufflers Black  with Chrome Swiss Cheese Billet Tips

    4" Harley-Davidson FLH FLT Dresser Road King Exhaust Mufflers Black with Chrome Swiss Cheese Billet Tips

    $165.00

    BLACK CHROME SLIP ON MUFFLERS FOR FLH MODELS
    with SWISS CHEESE Billet Tips
     
    • Fit 1995 -15 Harley-Davidson touring models FLHR, FLHRC, FLHRS, FLHTCU, FLTR, FLHX ( EXC. 2010 FLHX, FLTRX ) 
    • Triple plated chrome finish Tips
    • Steady, tough, low rumble
    • Utilize venturi chamber design baffle design to create smoothest power band
    • Race-proven baffle increases torque and horsepower
    • Unique internal baffle heat shield design
    • 1-3/4" inlets allow for OEM headers and heat shields
    • 32" in length
    • Massive 4" outlets on 4" mufflers with chrome billet tips for outstanding look
    • Sold in pairs 

    Fit 1995 -15 Harley-Davidson touring models FLHR, FLHRC, FLHRS, FLHTCU, FLTR, FLHX ( EXC. 2010 FLHX, FLTRX )

     

     

    Learn More
  17. Gas Tank stock Dash Kit Harley-Davidson Baggers Dresser Touring FLH FLHT FLTR Road King 08-2017 paul yaffe

    Gas Tank stock Dash Kit Harley-Davidson Baggers Dresser Touring FLH FLHT FLTR Road King 08-2017 paul yaffe

    $179.99

    Bagger Nation Custom Gas Tank Dash Kit for Touring Models 2008-2016

    This kit fits Stock OEM Touring model tanks with round Fuel Pump. NEW Clean And Simple Steel Dresser Dash design is a custom and sick look for all the new 2008-2017 6 gallon HD tanks! When the late model HD Touring gas tank got bigger, so did the OEM dash. So this is a quick and simple way to swap over with two simple mounts to make your stock bulky tank look completely custom and tricked out. This dash is completely metal and can be custom paited to match your bike or chromed out to make it pop. Get your dash kit quick to make your bike bad ass.The dash is a simple, direct bolt on application to your stock tank and really creates a sick look to your tank area!
    Tank kit includes a custom low profile steel dash, chrome pop-up gas cap, rubber trim and any necessary mounting brackets.

    21" between main mounting holes.
    22" long

    2008 - 2017 Harley-Davidson Electra Glide Classic (EFI) - FLHTC
    2008 - 2009 Harley-Davidson Electra Glide Standard (EFI) - FLHT
    2008 - 2017 Harley-Davidson Electra Glide Ultra Classic (EFI) - FLHTCU
    2015 - 2017 Harley-Davidson Electra Glide Ultra Classic Low-FLHTCUL
    2010 - 2017 Harley-Davidson Electra Glide Ultra Limited - FLHTK
    2015 - 2017   Harley-Davidson Freewheeler-FLRT
    2008 - 2009  Harley-Davidson Road Glide (EFI) - FLTR
    2010 - 2017  Harley-Davidson Road Glide Custom - FLTRX
    2015 - 2017   Harley-DavidsonRoad Glide Custom - FLTRX
    2015 - 2017  Harley-DavidsonRoad Glide Special-FLTRXS
    2011 - 2013  Harley-Davidson Road Glide Ultra - FLTRU
    2008 - 2017  Harley-Davidson Street Glide (EFI) - FLHX
    2014 - 2017  Harley-Davidson Street Glide Special - FLHXS
    2010 - 2011  Harley-Davidson Street Glide Trike - FLHXXX
    2009 - 2017  Harley-Davidson Tri Glide Ultra Classic - FLHTCUTG
    2015 - 2017  Harley-Davidson Ultra Limited Low-FLHTKL


    Fits 2008-16 Harley-Davidson Touring FLHT/FLTR models
    Will fit Road King 2008-11 models with custom dash modifications
    May custom fit 2003-07 Touring models
     

     

    Learn More
  18. Custom Gas Tank stock oem Dash Kit Harley-Davidson Baggers Dresser Touring FLH FLHT FLTR Road King 08-2017

    Custom Gas Tank stock oem Dash Kit Harley-Davidson Baggers Dresser Touring FLH FLHT FLTR Road King 08-2017

    $149.99

    Bagger Nation Custom Gas Tank Dash Kit for Touring Models 2008-2017 for Stock OEM

    This kit fits Stock OEM Touring model tanks . NEW Clean And Simple Steel Dresser Dash design is a custom and sick look for all the new 2008-2017 6 gallon HD tanks! When the late model HD Touring gas tank got bigger, so did the OEM dash. So this is a quick and simple way to swap over with two simple mounts to make your stock bulky tank look completely custom and tricked out. This dash is completely metal and can be custom paited , powerdercoated to match your bike or chromed out to make it pop. Get your dash kit quick to make your bike bad ass.The dash is a simple, direct bolt on application to your stock tank and really creates a sick look to your tank area!
    Tank kit includes a custom low profile steel dash, chrome pop-up gas cap, rubber trim and any necessary mounting brackets.

    21" between main mounting holes.
    22" long

    2008 - 2013 Harley-Davidson Electra Glide Classic (EFI) - FLHTC
    2008 - 2009 Harley-Davidson Electra Glide Standard (EFI) - FLHT
    2008 - 2017 Harley-Davidson Electra Glide Ultra Classic (EFI) - FLHTCU
    2015 - 2017 Harley-Davidson Electra Glide Ultra Classic Low-FLHTCUL
    2010 - 2017 Harley-Davidson Electra Glide Ultra Limited - FLHTK
    2015 - 2017  Harley-Davidson Freewheeler-FLRT
    2008 - 2009  Harley-Davidson Road Glide (EFI) - FLTR
    2010 - 2013  Harley-Davidson Road Glide Custom - FLTRX
    2015 - 2017  Harley-DavidsonRoad Glide Custom - FLTRX
    2015 - 2017  Harley-DavidsonRoad Glide Special-FLTRXS
    2011 - 2013  Harley-Davidson Road Glide Ultra - FLTRU
    2008 - 2017  Harley-Davidson Street Glide (EFI) - FLHX
    2014 - 2017  Harley-Davidson Street Glide Special - FLHXS
    2010 - 2011  Harley-Davidson Street Glide Trike - FLHXXX
    2009 - 2017  Harley-Davidson Tri Glide Ultra Classic - FLHTCUTG
    2015 - 2017   Harley-Davidson Ultra Limited Low-FLHTKL


    Fits 2008-16 Harley-Davidson Touring FLHT/FLTR models
    Will fit Road King 2008-11 models with custom dash modifications
    May custom fit 2003-07 Touring models
     

     

    Learn More
  19. El Diablo Black 13" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles

    El Diablo Black 15" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles

    $129.00

    "EL DIABLO" BLACK APEHANGERS
    15" Rise 1-1/4" Handlebars


    To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present including.
    May work on throttle-by-wire models with custom fitting and any custom application.
     
    These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.
     
    Powdercoated black!
    15" rise. 11" backward sweep.
    1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
    3-1/2 on-center knurling for firm mounting.
    37" wide from tip to tip.
    Come with drilled wiring holes.
     
    Black finish

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4-nch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Learn More
  20. El Diablo Black 13" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles

    El Diablo Black 13" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles

    $129.00

    "EL DIABLO" BLACK APEHANGERS
    13" Rise 1-1/4" Handlebars


    To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present including.
    May work on throttle-by-wire models with custom fitting and any custom application.
     
    These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.
     
    Powdercoated black!
    13" rise. 11" backward sweep.
    1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
    3-1/2 on-center knurling for firm mounting.
    37" wide from tip to tip.
    Come with drilled wiring holes.
     
    Black finish

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4-nch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Learn More
  21. El Diablo Chrome 16" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles

    El Diablo Chrome 15" Rise Ape Hangers 1-1/4" Diameter Handlebars for Harley Dressers Baggers FLHT FLHTC Motorcycles

    $129.00

    "EL DIABLO" CHROME APEHANGERS
    15" Rise 1-1/4" Handlebars


    To fit Harley-Davidson Touring models, Dressers, Baggers, FLHT, FLHTC from 1982 to present. May work on throttle-by-wire models with custom fitting and any custom application.
     
    These swedged handlebars have transition from the 1-1/4" diameter to the 1" area for mounting the stock OEM style 1" handlebar controls. These bars are made with CNC bender for a smooth radius at each bend.
     
    Triple-plated chrome!
    15" rise. 11" backward sweep.
    1-1/4"-diameter. Center section and tips taper to 1" so that standard handlebar controls fit.
    3-1/2 on-center knurling for firm mounting.
    37" wide from tip to tip.
    Come with drilled wiring holes.
     
    Chrome finish

     

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4-nch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Learn More
  22. 12" Rise BLACKOUT Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles

    12" Rise BLACKOUT Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles

    $575.55

    Black 12" Rise 'El Diablo' Ape Hangers
    with Black Hand Control Kit
    and Black Switches

    For Harley-Davidson Touring (Dresser / Bagger) models W/ Cruise Control from 1996 to 2012

    May work on throttle-by-wire models with custom fitting and any custom application

    (Only for models with CRUISE and RADIO ONLY)

    This listing is for complete 1-1/4" fat handlebar set-up. All components are Powder coated Black top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.

    All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
    Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.

    This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.

    Here is what you are getting:

    Smooth-Contour Hand Controls
    Unique design has hidden underside mounting
    on the switch housings for
    an unobstructed smooth, rounded surface on the top housing.
    BETTER LOOK AND CHROME THAN ANY HD PRODUCT.
    11/16" Bore master cylinder. For dual disc application.
    with radio controls and  cruise control

    This is top quality kit.
    Much higher quality than HD or any aftermarket product. Simply the best.


    Retail $402.99

    ----------------------------------------------------------------


    Black 'El Diablo'
    Swedged Apehangers
    12" Rise 1-1/4" Handlebars
    for Bagggers/Dressers

    Show Black!
    12" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
    37" wide from tip to tip.
    Come with drilled wiring holes.

    Retail $210.99

    --------------------------------------------------------------

    Black Switches and Wire Harness

    High quality Black switches for Dresser hand controls with radio control and cruise control.
    Wires are soldered and color-coded for easy installation.

    Retail $206.99

    ---------------------------------------------------------------

    Total package price: 402.99
    210.99
    206.99
    Professional Installation 235.00
    _________________
    Total: $1055.97

     

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4-nch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Learn More
  23. 13" Rise BLACKOUT Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles

    13" Rise BLACKOUT Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers W/ Cruise Control 1996-2012 Motorcycles

    $575.55

    Black 14" Rise 'El Diablo' Ape Hangers
    with Black Hand Control Kit
    and Black Switches

    For Harley-Davidson Touring (Dresser / Bagger) models W/ Cruise Control from 1996 to 2012

    May work on throttle-by-wire models with custom fitting and any custom application

    (Only for models with CRUISE and RADIO ONLY)

    This listing is for complete 1-1/4" fat handlebar set-up. All components are Powder coated Black top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.

    All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
    Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.

    This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.

    Here is what you are getting:

    Smooth-Contour Hand Controls
    Unique design has hidden underside mounting
    on the switch housings for
    an unobstructed smooth, rounded surface on the top housing.
    BETTER LOOK AND CHROME THAN ANY HD PRODUCT.
    11/16" Bore master cylinder. For dual disc application.
    with radio controls and  cruise control

    This is top quality kit.
    Much higher quality than HD or any aftermarket product. Simply the best.


    Retail $402.99

    ----------------------------------------------------------------


    Black 'El Diablo'
    Swedged Apehangers
    14" Rise 1-1/4" Handlebars
    for Bagggers/Dressers

    Show Black!
    14" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
    37" wide from tip to tip.
    Come with drilled wiring holes.

    Retail $210.99

    --------------------------------------------------------------

    Black Switches and Wire Harness

    High quality Black switches for Dresser hand controls with radio control and cruise control.
    Wires are soldered and color-coded for easy installation.

    Retail $206.99

    ---------------------------------------------------------------

    Total package price: 402.99
    210.99
    206.99
    Professional Installation 235.00
    _________________
    Total: $1055.97

     

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4-nch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Learn More
  24. 13" Rise Black Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers With Cruise Control 1996-2012 Motorcycles

    13" Rise Black Ape Hangers "El Diablo" Fat 1-1/4" Diameter with Hand Controls for Harley Dressers Baggers With Cruise Control 1996-2012 Motorcycles

    $575.55

    Black 13" Rise 'El Diablo' Ape Hangers
    with Hand Control Kit
    and Chrome Switches W/ Cruise Crontrol

    For Harley-Davidson Touring (Dresser / Bagger) models with Cruise Control from 1996 to 2012

    May work on throttle-by-wire models with custom fitting and any custom application

    (Only for models with CRUISE and RADIO ONLY)

    This listing is for complete 1-1/4" fat handlebar set-up. All components are triple-plated chrome top quality parts, featuring smooth hidden mounting hand controls, hidden wiring and chrome switches.

    All components are brand new and have been assembled by professional Harley-Davidson certified mechanic.
    Official Harley-Davidson service guidebook rates the hand switches wire installation job as a 2.5 hour job, valued at $235.

    This handlebars come fully and professionally assembled, ready to be installed on your motorcycle in minutes.

    Here is what you are getting:

    Smooth-Contour Hand Controls
    Unique design has hidden underside mounting
    on the switch housings for
    an unobstructed smooth, rounded surface on the top housing.
    BETTER LOOK AND CHROME THAN ANY HD PRODUCT.
    11/16" Bore master cylinder. For dual disc application.
    with radio controls and  cruise control

    This is top quality kit.
    Much higher quality than HD or any aftermarket product. Simply the best.


    Retail $402.99

    ----------------------------------------------------------------


    Black 'El Diablo'
    Swedged Apehangers
    13" Rise 1-1/4" Handlebars
    for Bagggers/Dressers

    Show Black!
    13" rise. 11" backward sweep. 1 1/4"-diameter. Center section tapers to 1" so that standard handlebar controls fit.
    37" wide from tip to tip.
    Come with drilled wiring holes.

    Retail $210.99

    --------------------------------------------------------------

    Chrome Switches and Wire Harness

    High quality chrome switches for Dresser hand controls with radio control and cruise control.
    Wires are soldered and color-coded for easy installation.

    Retail $206.99

    ---------------------------------------------------------------

    Total package price: 402.99
    210.99
    206.99
    Professional Installation 235.00
    _________________
    Total: $1055.97

     

     

     

     

    How to Install New Handlebar

    Ever notice how most fine artists depict the devil? They draw this demon
    from hells wings as having sharp angles. This vision was not lost on
    Demons Cycles. Its new 1 1/4"-inch El Diablo handlebars sure remind us of
    devil wings. No matter the imagery, we thought they have a real cool look, as
    did Navy Seaman Mario Guerrero.

    1. The El Diablo handlebars owe their sinister look to their severe angles and gusset plates. They are

    fabricated from 1 1/4"-inch tubing and powder coated black.

    2. Our starting point, a 2007 Dyna Street-Bob: the dash, gas tank, and hand controls already have been removed.

    3. The new handlebars have oblong holes to run the control wiring in and out through.

    4.  air nozzle is used to blow the lead  string through the bars,Then a length of
    rope is attached to the string and pulled through
    the bars.

    5. The rope was used to pull the controls wire harnesses through the bars.

    6. The factory risers wer used to mount the new bars.

    7. Because the bars are T inch in diameter at  their center mounting position, a stock
    clamp was used

    8. The control switches were mounted to the bars and their harnesses fined over the top triple tree and routed into the frame.

    9. The switch wiring exits the front of the switch housing and into the bars.

    10. Once the switch houseing were in the place the front brake and clutch levers were attached to the bars

    11. These stunning bars sure remind us of devil wings.

    Learn More

Items 1 to 24 of 43 total

per page

Grid  List 

Set Descending Direction